How Ro Fix Playstation Control My Charec Tor Keeps Going Around

Download Article

Download Commodity

This wikiHow teaches yous how to set a PS3 controller. Ane of the most mutual problems with PS3 controllers is random button pushes. At that place is a fairly like shooting fish in a barrel fix to this problem, but information technology will crave disassembling your controller. Other problems y'all may encounter are dislodged analogue sticks, and h2o damage.

i

Remove screws from the back of the controller. There are five screws holding the controller together. At that place are two on the top and bottom of both sides, and one on the top heart.
2
Remove the back. Yous may need to pry open up the controller with a apartment head screwdriver. Open information technology from the bottom and carefully tilt it towards the height shoulder buttons.
- Be very careful that y'all don't accidentally dislodge the R2 or L2 trigger buttons while removing the back. They can be pain to put dorsum on.
Advertisement
3
Remove the bombardment. The battery is the grey square piece on the back of the motherboard. You don't need to disconnect the bombardment. You can just pull it upward out of it'south holder and motion information technology to the side.
- If you practise decide to disconnect the bombardment, pull on the white plastic role that the wires are connected to. Exercise not pull on the wires.
4

Remove the screw on the motherboard. The motherboard spiral is located on the lesser of the motherboard next to the analogue stick.
5
Remove the motherboard. Carefully pull the motherboard upwardly and tilt information technology away from the shoulder buttons.
- One time again, be careful non to accidentally dislodge the R2 and L2 trigger buttons.
half-dozen

Lift the green ribbon and pull it back. The light-green ribbon is located at the top of the controller front end. Information technology'south in a higher place the hole where the left analogue stick goes. Place a flat head screwdriver under the ribbon and carefully lift it up over the two plastic pins that are sticking up out of the controller. Be careful not to tear or damage the ribbon. You volition see a strip of black foam underneath the ribbon.
7

Remove the black cream strip. Over time, the foam strip gets compressed and the connectors on the ribbon aren't able to make contact with the motherboard. This is why the controller is not working properly.
8
Identify record on the bottom of the blackness foam strip. For the all-time results, cut a strip of thick double-sided tape the same length and width every bit the blackness foam strip. Identify information technology under the foam strip. Use scissors to cut off any excess tape from the sides.
- If you don't have thick double-sided tape, you tin can cut about an inch-and-a-half of black electrical tape and curl information technology up into a tube. ^[1]
nine

Replace the cream strip. With the tape underneath the foam strip, you can now identify the cream strip back under the ribbon.
ten

Replace the ribbon. Pull the ribbon over the cream and place the two holes over the pins that are sticking up out of the controller. Brand certain it is firmly in place.
11

Clean the ribbon. Since the controller is open, information technology'south not a bad idea to use a tissue or cotton swap to wipe whatever dust away from the ribbon.
12

Clean the motherboard connector. If you look at the motherboard, you will see a box that is a darker shade of green with some metal connectors sticking out of it. It's above the left counterpart stick. This is where the motherboard connects to the ribbon. Use a tissue or cotton swap to wipe the connectors on the mother board.
thirteen

Supercede the motherboard. Carefully identify the motherboard dorsum in it'due south identify with the counterpart sticks freely able to move through the holes.
14

Screw the motherboard back in place. Using the same screw you took out of the motherboard, screw it back in at the lesser next to the right analogue stick.
xv

Replace the battery. The motherboard has a plastic holder on information technology'due south dorsum that holds the battery in place. Identify the bombardment back in the holder.
16
Replace the controller dorsum. To replace the controller back, place the the thin role that goes in between the two shoulder buttons at the top of the controller in identify. Carefully tilt the back over the R2 and L2 trigger buttons and firmly push information technology back in identify at the lesser of the controller.
- Be conscientious not to accidentally dislodge the R2 and L2 trigger buttons.
17

Replace the screws on the controller dorsum. In that location are 5 screws that hold the controller together. Replace the two on the sides, and the ane in the middle. Your controller is at present stock-still.^[2]

1

Remove screws from the back of the controller. In that location are five screws holding the controller together. There are two on the tiptop and bottom of both sides, and one on the pinnacle heart.
2
Remove the back. You lot may need to pry open the controller with a flat head screwdriver. Open it from the bottom and carefully tilt it towards the top shoulder buttons.
- Be very careful that y'all don't accidentally dislodge the R2 or L2 trigger buttons while removing the dorsum. They can be pain to put back on.
3
Remove the bombardment. The battery is the big gray square on the dorsum of the motherboard. You don't need to disconnect the battery. You lot tin can just pull it up out of it's holder and motility it to the side.
- If you do decide to disconnect the bombardment, pull on the white plastic role connected to the circuit lath. Don't pull on the wires.
4

Remove the spiral on the motherboard. The motherboard spiral is located on the lesser of the motherboard side by side to the analogue stick.
5
Remove the motherboard. Carefully pull the motherboard up and tilt it away from the shoulder buttons.
- Once again, be careful not to accidentally dislodge the R2 and L2 trigger buttons.
vi

Identify the plastic stick back on the metal rod. At that place is a D-shaped metal rod that sticks up out of the motherboard. Place the plastic analogue stick back on the metal rod.
seven

Replace the motherboard. Advisedly place the motherboard back in it'due south identify with the analogue sticks freely able to move through the holes.
8

Screw the motherboard back in place. Using the same screw y'all took out of the motherboard, screw it back in at the bottom adjacent to the right analogue stick.
9

Replace the battery. The motherboard has a plastic holder on it's back that holds the bombardment in place. Place the battery back in the holder.
ten
Supersede the controller back. To supersede the controller dorsum, identify the the thin part that goes in between the two shoulder buttons at the summit of the controller in place. Carefully tilt the back over the R2 and L2 trigger buttons and firmly push it back in place at the bottom of the controller.
- Be very careful not to dislodge the R2 and L2 trigger buttons.
11

Replace the screws on the controller back. In that location are five screws that hold the controller together. Supervene upon the two on the sides, and the ane in the middle. Your controller is now fixed.

Advertising

1

Power off the controller immediately. If the controller gets wet, turning off the ability immediately will prevent the circuit board from shorting out.
two

Remove screws from the back of the controller. There are five screws holding the controller together. At that place are two on the top and lesser of both sides, and one on the top middle.
three

Remove the back. You lot may need to pry open up the controller with a flat head screwdriver. Open up it from the bottom and advisedly tilt it towards the peak shoulder buttons.
4

Disconnect the bombardment. The battery is the large grey square on the back of the motherboard. To disconnect the bombardment, pull the white plastic slice that connects to the motherboard. Do not pull on the wires. Pull on the plastic piece.
5

Place the controller under a lamp, fan, or window. This will help the h2o in the controller evaporate.
vi

Wait at least 24 hours. To ensure the controller is completely dry expect 24 hours, or longer.
7

Reconnect the battery. Replace the white plastic part that the bombardment wires are connected to back in the white plastic connector on the side of the motherboard.
viii
Replace the controller dorsum. To supervene upon the controller back, place the the sparse role that goes in between the two shoulder buttons at the meridian of the controller in place. Carefully tilt the dorsum over the R2 and L2 trigger buttons and firmly push it back in identify at the bottom of the controller.
- Be careful non to accidentally dislodge the R2 and L2 trigger buttons.
9

Supplant the screws on the controller dorsum. There are five screws that hold the controller together. Supplant the two on the sides, and the one in the eye.
10

Test the controller. To properly test the controller, launch a game that utilizes all the buttons on the controller (similar Minecraft). Test every button to make sure they are practise what they are supposed to do. If all the buttons are working, the controller is fixed. If there is any random button presses, or buttons not working, the motherboard has a brusk in it. You volition demand to supervene upon the controller.

Advertising

Add New Question

Question

How do I fix a scratched PS3 deejay?

Try putting mint Colgate toothpaste on information technology, just a tiny dab. Gently wipe the excess toothpaste off with a newspaper towel. Y'all tin can see some different methods in the article How to Fix a Scratched CD.
Question

How practise I fix an analog stick that sometimes gets stuck in certain positions?

Commonly, information technology's just dingy. Open it every bit described and clean it with some booze.
Question

My dualshock's battery is still unusable after two hours of charging. All the lights are blinking for 2 hours but still can't apply it. What's the problem and how to ready it?

Toasterflame

Top Answerer

Information technology may exist that the battery on your controller has failed. Many repair shops can replace the bombardment for you. Or, if you are familiar with electronic repair, you lot tin find many guides on this site to mend it yourself.